文章中心ARTICLE CENTER
在發展中求生存,不斷完善,以良好信譽和科學的管理促進企業迅速發展產品中心
PRODUCT CATEGORY相關文章
RELATED ARTICLES
詳細介紹
本機由機座、機頭、減速箱、工作臺、切角刀、拖板等零部件組成。
電機通過減速箱減速后,帶動飛輪旋轉,當扳下操作手柄(圖(2)中14)或踩下踏板(圖(2)中19)時,開關座(12)即與飛輪(11)嚙合,從而使偏心輪(3)轉動,再通過連桿(2)帶動切角刀(15)作上下裁切運動。
This machine is made up of parts and components such as machine seat, machine head, speed reduction box, worktable, cutter and towing board.
After the motor decelerates through the speed reducer, it drives the flywheel to rotate. When the handle is pulled down(14 in Figure 2) or the pedal is stepped down(19 in Figure 2), the switch seat(12) is engaged with the flywheel(11)., In this way, the eccentric wheel(3) is rotated, and then the cutting cutter(15) is driven by the connecting rod(2) for up and down cutting motion. 用于筆記本,精裝書,紙張、紙板、PVC.包裝袋,軟包裝,吊牌等多種軟性材料的圓角切割。廣東書籍SJQ平角圓角切角機操作

Δ注意事項matters needing attention:
一、?工作期間注意力集中,嚴格遵守設備操作規程,做到安全作業。
二,調整設備前首先切斷電源。
三、根據產品規格的尺寸要求,進行精確調整,調整時需使用**工具,小心仔細,注意安全。
First, pay attention during the work, strictly observe the equipment operating rules, to achieve safe operations.
Second, cut off the power before adjusting the equipment.
Third, according to the size requirements of the product specifications, make precise adjustments. When adjusting, use special tools, be careful and pay attention to safety. 廣東書籍SJQ平角圓角切角機操作誠信求實、團結進取、創新高效。

試車Test run在機器安裝好后,在接通電源試車,試車前應將各注油孔、滑動面、,注入潤滑油,開機前用手扳動偏心輪(圖(2)中3),使切刀做一、兩次循環運動,檢查機器是否正常,電機轉動方向應與偏心輪上箭頭所指方向相同,否則裁切時會導致機器非正常損壞。可打開機器左側小門,觀察飛輪轉向(圖(2)中11)是否與偏心輪上箭頭所指方向一致。
After the machine is installed, before the power supply test is connected, each injection hole, sliding surface, and lubricating oil should be injected before the test, and the eccentric wheel should be pulled by hand before starting(Figure(2) in 3). Make the cutter do one or two cycles of movement, check whether the machine is normal, the direction of motor rotation should be the same as the direction indicated by the arrow on the center wheel, otherwise the cutting will cause abnormal damage to the machine. The small door on the left side of the machine can be opened to see whether the flywheel steering(11 in Figure(2)) is consistent with the direction indicated by the arrow on the center wheel.
SJQ-120A切角機適用于吊牌、鋁塑包裝袋、護卡膜、存折、筆記本、書籍等類似產品的圓角沖切。本公司生產的SJQ-120A,設計結構精細緊湊,操作方便簡易,性能穩定可靠,可以更換不同切角的規格,廣泛應用于各種印刷企業,是辦公自動化相當有理想的裁切設備。可適用于裁切各種筆記本、吊牌、護卡膜、鋁塑包裝袋、名片、書籍、信封、商標、撲克牌等印刷品的圓角與平角;以及軟盒煙標的左30°右60°斜角。特殊產品可以按需定制,適用于各種包裝類產品以及畫布包角的產品裁切。SJQ-120A型切角機除各種圓角外,亦可裁切精裝封面平角及軟包裝斜角之用。
在未來的時間段里,我們自信著可以為客戶、社會創造更多的價值。

圓角封面機的給紙部分由給紙臺、輸紙頭、接紙輪、雙張檢測裝置、輸紙臺等部件組成,其功能是把紙張準確平穩地輸送到上膠部位。機器給紙臺板放置在前后三根橫檔上,堆放紙張時,紙張的中心一般應對準機器的中心,紙張前邊緣應靠齊前齊紙板,轉動手輪,調節側擋紙規左右位置靠齊紙堆。電器按鈕面板上設有給紙臺升降按鈕,按此兩個按鈕,可使紙臺快速上升或者下降。(注意:紙堆快速上升時一定要使壓腳處于紙堆的后邊緣并處于低位置)先壓后切,圓角更準確。廣東書籍SJQ平角圓角切角機操作
生產實力、展望未來。廣東書籍SJQ平角圓角切角機操作
現如今,新型包裝機械普遍具備多功能、調整操作簡單等條件,機電一體化是包裝控制器的新趨勢。通過此次統計發現,新型包裝機械將配合產業自動化趨勢,新型設備及技術得到了普及。封面機對不利因素,**緊迫的是改變包裝機械行業中各企業的發展方式。相信我們的SJQ圓角機以它技術優勢,一定會帶給客戶帶來不一樣的體驗。圓角封面機區別于傳統的封面機,實現了多種功能的組合,一機多用,能滿足不同客戶的多樣化需求。讓廣大客戶在機器的選擇上多了一份參考,也讓我們的公司競爭力有所提高。廣東書籍SJQ平角圓角切角機操作
溫州市旭日印刷機械有限公司主要經營范圍是機械及行業設備,擁有一支專業技術團隊和良好的市場口碑。公司業務分為沖切抹角機,切角機,挖月機,壓緊機等,目前不斷進行創新和服務改進,為客戶提供良好的產品和服務。公司從事機械及行業設備多年,有著創新的設計、強大的技術,還有一批專業化的隊伍,確保為客戶提供良好的產品及服務。在社會各界的鼎力支持下,持續創新,不斷鑄造***服務體驗,為客戶成功提供堅實有力的支持。
產品咨詢